Summary
The fuselage of the next generation of Large Passenger Aircrafts´ (LPA) will be made with thermoplastic (TP) composites. In fact, even if this kind of materials are being increasingly used in aerospace industry, as they contribute to lighter aircrafts and consequently to fuel consumption reduction, there are still some issues to be overcome until this becomes a reality.
The manufacturing complex forms of rear end section with continuous fibre-reinforced TP still poses a considerable challenge: higher processing temperatures and raw material costs, need of complex temperature-controlled tooling, etc. Automated fibre placement (AFP) is a workable alternative for more complicated TP Composites (TPC) shapes with varying part thickness (e.g., fuselage shells, wing and stabilizer torsion boxes and stringers), but one of the challenges is void removal, which is more difficult with TP than with thermosets.
FRAMES aims to fully define technical and cost performance of an optimized integral TP rear end manufacturing process with critical design features as an alternative to thermoset materials. Thanks to a self-heated tool with process driven heating zones and advanced lay up process simulation, FRAMES will be capable of predicting heating law for efficient TP-AFP, correlated with lay-up trials, mastering TP-stiffeners manufacturing process, optimizing co-consolidation cycle. Its main innovation relies on the co-consolidation of a double curved and thick skin with its entire stiffening structure in one shot.
FRAMES will support the spread of alternative heating process for thermoplastic AFP by developing a simulation tool able to predefine processing parameters of the most common aerospace grades thermoplastics. At the end, the advanced rear end (ARE) concept that will allow the savings (NRC and maintenance costs, higher integration level at lighter weight, etc.) will be easily applicable to other panels or structures with the same interface principle or same architecture
The manufacturing complex forms of rear end section with continuous fibre-reinforced TP still poses a considerable challenge: higher processing temperatures and raw material costs, need of complex temperature-controlled tooling, etc. Automated fibre placement (AFP) is a workable alternative for more complicated TP Composites (TPC) shapes with varying part thickness (e.g., fuselage shells, wing and stabilizer torsion boxes and stringers), but one of the challenges is void removal, which is more difficult with TP than with thermosets.
FRAMES aims to fully define technical and cost performance of an optimized integral TP rear end manufacturing process with critical design features as an alternative to thermoset materials. Thanks to a self-heated tool with process driven heating zones and advanced lay up process simulation, FRAMES will be capable of predicting heating law for efficient TP-AFP, correlated with lay-up trials, mastering TP-stiffeners manufacturing process, optimizing co-consolidation cycle. Its main innovation relies on the co-consolidation of a double curved and thick skin with its entire stiffening structure in one shot.
FRAMES will support the spread of alternative heating process for thermoplastic AFP by developing a simulation tool able to predefine processing parameters of the most common aerospace grades thermoplastics. At the end, the advanced rear end (ARE) concept that will allow the savings (NRC and maintenance costs, higher integration level at lighter weight, etc.) will be easily applicable to other panels or structures with the same interface principle or same architecture
Unfold all
/
Fold all
More information & hyperlinks
Web resources: | https://cordis.europa.eu/project/id/886549 |
Start date: | 01-07-2020 |
End date: | 31-12-2022 |
Total budget - Public funding: | 1 191 636,00 Euro - 868 261,00 Euro |
Cordis data
Original description
The fuselage of the next generation of Large Passenger Aircrafts´ (LPA) will be made with thermoplastic (TP) composites. In fact, even if this kind of materials are being increasingly used in aerospace industry, as they contribute to lighter aircrafts and consequently to fuel consumption reduction, there are still some issues to be overcome until this becomes a reality.The manufacturing complex forms of rear end section with continuous fibre-reinforced TP still poses a considerable challenge: higher processing temperatures and raw material costs, need of complex temperature-controlled tooling, etc. Automated fibre placement (AFP) is a workable alternative for more complicated TP Composites (TPC) shapes with varying part thickness (e.g., fuselage shells, wing and stabilizer torsion boxes and stringers), but one of the challenges is void removal, which is more difficult with TP than with thermosets.
FRAMES aims to fully define technical and cost performance of an optimized integral TP rear end manufacturing process with critical design features as an alternative to thermoset materials. Thanks to a self-heated tool with process driven heating zones and advanced lay up process simulation, FRAMES will be capable of predicting heating law for efficient TP-AFP, correlated with lay-up trials, mastering TP-stiffeners manufacturing process, optimizing co-consolidation cycle. Its main innovation relies on the co-consolidation of a double curved and thick skin with its entire stiffening structure in one shot.
FRAMES will support the spread of alternative heating process for thermoplastic AFP by developing a simulation tool able to predefine processing parameters of the most common aerospace grades thermoplastics. At the end, the advanced rear end (ARE) concept that will allow the savings (NRC and maintenance costs, higher integration level at lighter weight, etc.) will be easily applicable to other panels or structures with the same interface principle or same architecture
Status
CLOSEDCall topic
JTI-CS2-2019-CfP10-LPA-01-81Update Date
26-10-2022
Images
No images available.
Geographical location(s)
Structured mapping
Unfold all
/
Fold all